top of page
White coach bus

Rack Specifications

Deck Height - 24 inches

Radius of Pulling - 360 degrees

Deck Width - 102 inches

Treadway Width - 36 inches

Center opening - 30 inches

Deck length choices - 20, 40, 60, 80 ft.

Choose air, or electric hydraulicsEnerpac

Standard tower height - 10 ft.

Telescoping tower height - 14 ft. 6 in.

Standard tower hydraulics - 50 ton

Telescoping tower hydraulics - 50 & 15 ton

cent

The Centurion

TM

Discription

  • Largest and heaviest built rack in the industry

  • Swing & rolling towers move easily

  • All towers have push and pull capabilities

  • Ramps are on wheels and can be easily moved to either end, to drive on, drive off

  • Rack can be installed on the floor or in a pit

  • Choose electric or air hydraulics

  • 50 ton hydraulic ram in each tower

  • Independently moving towers allow true 360 degree pulling

  • Pull all the way around the rack, no dead spots on the corners

  • Heavy duty accessories available

  • 10 ft. tall towers

  • All towers move independently

  • 102 inch wide deck

  • Big 50 ton rams in towers

  • Optional telescoping tower pulls to 14 ft. 6 in.

  • Convenient air & hydraulic quick couplers located every 10 feet.

  • Large pressure gauges at each tower

  • Our deck design allows infinite holding and tie down locations

  • Shut off valves at each tower

  • Heavy duty ramps are on casters. Ramps can easily be rolled to either end so you can drive on and drive off.

  • Modular construction so you can add another section or tower as needed.

  • We stock heavy duty racks and accessories for fast delivery. Other companies build on order so you'll wait 60 to 120 days for your equipment.

Optional Rack Accessories

Hydraulic pump and cylinders, heavy duty frame straightening system
Heavy duty frame straightening system clamps with chain
Hook and wedges for a heavy duty frame straightening system
Roller assembly for heavy duty frame straightening system

Hydraulic Power
We use high quality hydraulics in our racks and accessories, and offer both electric and air hydraulics.

Rail Chain Protectors
​Hangs on the inside or outside of frame rail supports chain while anchoring and pulling. Prevents damage to rail flanges.

Hold-Down Anchor

Used with two opposing wedges Anchoring or pulling truck rail down. Can also be used for up pull.

Down Pull

With this convenient accessory you can pull down from anywhere on our deck.

Hydraulic ram for a heavy duty frame straightening system
Blue heavy duty frame straightening tool
Heavy duty frame straightening system component

Chain

We use only the best grade of 3/8" and 5/8" Columbus McKinnon chains and hooks with our equipment.

Frame Spread Block

Blocks hang on flange while cradling hydraulic ram (10, 15, 25 ton) Spread rails, even while making other pulls.

Flange Wrench

Adjustable head allows you to get just the right angle and leverage. For straightening light bends and crimps in frame rails.

Sliding Crossmember

This accessory gives you the ability to lift and make pushes from the center of the deck.

C-clamp and parts for a heavy duty frame straightening system
Blue components of a heavy duty frame straightening system
Heavy duty frame straightening system stand
Heavy duty frame straightening system support

25-Ton Flange Press

Straightens flange and web. Will remove dimples from radius of rail. Comes with air/hyd. pump and hose.

30-Ton Tight Area Flange Press

Straightens flange in areas around engine and other obstructions. Comes with air/hyd. pump and hose.

25 Ton Hydraulic Jack Stand

Un-extended ram height 19" at lowest pinned point 30" at highest pinned point. 45" with ram extended at highest pinned point with ram fully extended. Use for removing frame twist and sag. Use for re-arching flat-bed trailers.

25 Ton Hydraulic Jack Stand

25" at lowest point. 35" at highest point. Use as fulcrum on down pulls. Use under high corners while removing twist. Run anchoring chains over top of stand for horizontal anchor.

Blue metal clamp for heavy duty frame straightening system

Wide Flange Hook

For making horizontal pulls on frame rails. Wide, for more dispersion of pulling power.

Heavy duty frame straightening system hook with eyelet

Narrow Flange Hook

For making horizontal pulls on frame rails. Narrow, for getting into tight spots.

bottom of page